Automatic or automated test equipment (ATE) is a system that performs tests on a device, known as the Device Under Test (DUT), using automation to quickly perform measurements and evaluate the test results. An ATE can be a simple computer controlled digital multimeter, or, more often, a complicated system containing dozens of complex test instruments (real or simulated electronic test equipment) capable of automatically testing and diagnosing faults in complex ICs.

The ATE/semiconductor test segment is comprised of six distinct types of testers:
• Analog/Linear Test
• Mixed Signal Test
• RF/Microwave Test
• Digital/Logic Test
• Memory Test
• System-on-Chip (SOC) Test

ATE systems interface with packaged chips through a separate machine called an IC handler. Tested ICs are then “binned” depending on their performance (higher performance devices are sold at a premium). Alternatively, ATE systems can test unpackaged chip directly on the wafer through a wafer prober and probe card designed to touch on the IO/bonding pads of the device. In this way, the cost of packaging bad chips is avoided.

The ATE market is driven by semiconductor chip volumes. As chip volumes steadily increase, the demand for chip testers also grows.

Given the sharp increase in usage of memory devices in end products such as home appliances, cell phones, and automobiles, it’s no surprise that the memory tester sub-segment is the largest in the ATE space.

According to a research report by Radiant Insights, Inc., the global ATE mrket is expected to be valued at $4.48 billion by 2020, as per Increasing design complexity coupled with need for effective testing is expected to drive the global automated test equipment market demand.

Increasing need for optimizing power management in order to ensure longer battery life is likely to favor the growth prospects. However, dependency on semiconductor chips is likely challenge industry participants. Non-memory products were the leading segment, valued at $2,867.5 million in 2013, according to the report. Expansion of consumer electronics, increasing automotive demand and growing number of microcontroller-based applications are factors likely to promote its demand.

Memory products accounted for 21.21% of the overall revenue in 2013, growing at an estimated CAGR of 1.7% from 2014 to 2020. The cyclical variations in growth rates than non-memory semiconductors have resulted in gaining popularity among various applications.

Additional Reading:

Business is good for vendors of test and inspection/metrology equipment

SUPPLIERS


Boston Semi Equipment: www.bostonsemiequipment.com



CD Genomics: http://www.cd-genomics.com



Microtek: http://www.utekinc.com



MoviTHERM: http://movitherm.com



NanoFocus AG: www.nanofocus.com



ARTICLES



North American semiconductor equipment industry posts November 2016 book-to-bill ratio of 0.96

12/16/2016  A book-to-bill of 0.96 means that $96 worth of orders were received for every $100 of product billed for the month.

Murphy, Choh and Pilla join ClassOne Technology's Board of Advisors

12/01/2016  ClassOne Technology, manufacturer of advanced wet processing equipment for ≤200mm substrates, announced the formation of a Board of Advisors.

Managing particle flows in process exhaust for safety and profitability

10/28/2016  Solid particles in the abatement exhaust must be properly managed, and in some cases, substantially reduced from the gas stream before it is released into the environment.

Lam Research introduces dielectric atomic layer etching capability for advanced logic

09/07/2016  Lam Research Corp., an advanced manufacturer of semiconductor equipment, today announced that it is expanding its atomic layer etching (ALE) portfolio with the addition of ALE capability on its Flex dielectric etch systems.

Cabot Microelectronics appoints Thomas F. Kelly as VP of Corporate Development

09/02/2016  Cabot Microelectronics Corporation announced the appointment of Thomas F. Kelly, Vice President, Corporate Development, which is effective as of September 6, 2016.

Lam Research enables next-generation memory with industry's first ALD process for low-fluorine tungsten fill

08/09/2016  Lam Research Corp. (NASDAQ: LRCX), an advanced manufacturer of semiconductor equipment, today introduced an atomic layer deposition (ALD) process for depositing low-fluorine-content tungsten films, the latest addition to its ALTUS family of products.

Nitrous oxide no laughing matter

07/13/2016  N2O, or Nitrous Oxide, also known as laughing gas, is a weak anesthetic gas that has been in use since the late 18th century.

Samco boosts shipment capacity with second production center

06/21/2016  Samco, a Japan-based semiconductor processing equipment manufacturer, held a completion ceremony for its second production center on June 17.

Equipment spending up: 19 new fabs and lines to start construction

06/10/2016  While semiconductor fab equipment spending is off to a slow start in 2016, it is expected to gain momentum through the end of the year. For 2016, 1.5 percent growth over 2015 is expected while 13 percent growth is forecast in 2017.

ClassOne announces major savings with Solstice gold plating

06/02/2016  ClassOne Technology, manufacturer of budget-friendly wet processing equipment, is reporting significant savings in the plating of gold in ≤200mm applications using its Solstice systems.

Busch wins annual NXP Semiconductors Best Supplier Award

05/25/2016  NXP Semiconductors N.V. announced Busch Semiconductor Vacuum Group LLC as the Best Supplier for Front-end equipment (semiconductor equipment) at NXP’s first Supplier Day Awards ceremony in Austin, Texas.

Global semiconductor sales increase slightly in March

05/06/2016  The Semiconductor Industry Association (SIA) this week announced worldwide sales of semiconductors reached $26.1 billion for the month of March 2016, a slight increase of 0.3 percent compared to the previous month's total of $26.0 billion.